Block ein- oder ausblenden

Hauptmenü

 Главная Сообщество Возможности для подписавшихся Форумы

Выберите язык

Český English Français Deutsch Italiano Polski РУССКИЙ

Top plate in wall (or gypsum) as bottom plate for roof???

Q/A about D-Wall, D-Roof, D-Floor/ Ceiling, D-CAM
Ответить на темуОтветить на тему Напечатать текущую страницу
На страницу 1, 2  След.

Top plate in wall (or gypsum) as bottom plate for roof???

Создавать темы Добавлено: 25.05.2007 11:06

Is it possible to define the top beam (and gypsum(?)) as bottom plate for roof - so that rafters automatically get a birth mouth's cut around the edge of the wall (the edge of the outside gypsum).

As for now, I make this birth mouth manually in D-Cam, and it takes some time. Плачущий или очень расстроенный
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 12:26

No, that is not possible.

Perhaps you can use a little trick:
In roof design put in some purlins, they will make the birds mouths automatically. Be sure to have the line markings on the purlins. Then in Dicam you take each single purlin, and explode the line markings. At the same time, the birds mouths will be exploded, too (without manual treating every single rafter). Delete the purlins, and the birds mouths will stay!
_________________
Freundlich grüßt
Der_Planer

Der_Planer
Power-Experte
Power-Experte
 
Сообщения: 10213
Зарегистрирован: Aug 24, 2004
Откуда: 55218 Ingelheim

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 13:09

Ok - thank you - I will take a look at that, because I don't know what is a "purlin".
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 13:35

What is the correct word for the horizontal beams, where the rafters are nailed upon?
I thought it was "purlin"? Смущённый

Next update installation I should install more language files...
_________________
Freundlich grüßt
Der_Planer

Der_Planer
Power-Experte
Power-Experte
 
Сообщения: 10213
Зарегистрирован: Aug 24, 2004
Откуда: 55218 Ingelheim

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 14:07

Hi Planer,

it´s OK: "purlin" is the correct expression for "Pfette"!

Regards,

Jens
_________________
Grüße aus Neubiberg,

Jens Krause

Dietrich's AG

Jens Krause
Hyper-Poster
Hyper-Poster
 
Сообщения: 2079
Зарегистрирован: Mar 01, 2005
Откуда: Neubiberg

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 14:49

It might be "purlin", but I did not work with that - so that's why I don't know what it is.
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 25.05.2007 14:56

Hello Planer,
we should install an english version, so its better to translate the correct words Подмигнуть Смеющийся
_________________
Es grüßt der Doug

doug
Mega-Poweruser
Mega-Poweruser
 
Сообщения: 4755
Зарегистрирован: Jan 03, 2005
Откуда: Magrathea

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 11:46

I cannot find "purlin" in roof design, where is it supposed to be??

Another way could be to just put in plates (that will just run into the wall's top plate), and when finished, delete these plates - but then maybe the birth mouths will not stay??
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 12:12

It´s in roof- design 5-3 Подмигнуть
Normally it should work with the solution, make a screen- print or send the project to the forum, somebody will look at it Подмигнуть
_________________
Es grüßt der Doug

doug
Mega-Poweruser
Mega-Poweruser
 
Сообщения: 4755
Зарегистрирован: Jan 03, 2005
Откуда: Magrathea

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 12:34

OK. Подмигнуть I still see no 'purlin'.
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 12:39

....mmmh, ok, the translation says this Подмигнуть
_________________
Es grüßt der Doug

doug
Mega-Poweruser
Mega-Poweruser
 
Сообщения: 4755
Зарегистрирован: Jan 03, 2005
Откуда: Magrathea

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 13:00

So - is it bottom plates??
_________________
Sincerely Yours. M. Sc. E. Thorvald, Denmark
(Dietrichs version 7.03).

Thorvald
Tera Poster
Tera Poster
 
Сообщения: 1059
Зарегистрирован: Aug 16, 2006

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 13:18

Yes, it is the bottom-plate. You can also call it purlin.
_________________
Viele Grüße,
Joachim Neumann (Dietrich's AG)
Software für den Holzbau, Abbund, Holzrahmenbau, Blockbau, Ingenieurholzbau und für die Fertighausindustrie

if (ahnung == 0) { read "Tipps & Tricks"; use SEARCH; use Blog; } else { use brain; make post; }

Joachim Neumann
Moderator
Moderator
 
Сообщения: 26179
Зарегистрирован: Jul 07, 2004
Откуда: Neubiberg

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 14:24

A purlin is a horizontal member whos top face is in the plane of the roof. (5-3-4 in roof design.) A plate is a roof member whos sides are plumb and level.

If you have a midspan member (not rotated in the plane of the roof) with rafters framed over it, this is commonly called a purlin plate (5-3-2 in roof design). If you have a midspan member in the plane of the roof (it is rotated) and rafters frame into it, this is commonly called a principal purlin.

Not to get caught up in terminology, or anything.

Joe

jmiller
Dauerposter
Dauerposter
 
Сообщения: 85
Зарегистрирован: Oct 04, 2005
Откуда: UP of MI

Re: Top plate in wall (or gypsum) as bottom plate for roof??

Создавать темы Добавлено: 26.05.2007 14:46

Thorvald:
.... delete these plates - but then maybe the birth mouths will not stay??

Please read again the second post of this thread. If you follow it, the birds mouths will stay!
_________________
Freundlich grüßt
Der_Planer

Der_Planer
Power-Experte
Power-Experte
 
Сообщения: 10213
Зарегистрирован: Aug 24, 2004
Откуда: 55218 Ingelheim
Показать сообщения:   
Ответить на темуОтветить на тему Страница 1 из 2 На страницу 1, 2  След.

Timber Design Modules

Перейти:  



Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете голосовать в опросах
You cannot attach files in this forum
You cannot download files in this forum

Часовой пояс: GMT + 1 Hour